高压下β-InSe弹性常数、电子结构的第一性原理研究

基于密度泛函理论的第一性原理计算方法,本文研究了高压对β-InSe弹性常数、机械性能和电子结构的影响.在0～20 GPa范围内,随着压力的增大,β-InSe的晶格常数、晶胞体积逐渐减小,结构参数a/a_0、c/c_0、V/V_0单调减小.在0～12 GPa范围内,弹性模量G、E、B和泊松比v随着压力增大而增大,在16 GPa时大幅减小,G、E、B分别减小了34.9%、53.3%、82.9%.随着压力增大,Se-In和In-In原子之间的电荷密度增大,Se-In原子之间的共价键增强,层间距减小.而且,β-InSe在20 GPa时带隙消失,发生了半导体向半金属的相变.     

Efficient Quantum Dot Light-Emitting Diodes Based on Well-Type Thick-Shell CdxZn1−xS/CdSe/CdyZn1−yS Quantum Dots

Device grade quantum dots (QDs) require QDs ensembles to retain their original superior optical properties as in solution. QDs with thick shells are proven effective in suppressing the inter-dot interaction and preserving the emission properties for QDs solids. However, lattice strain–induced defects may form as the shell grows thicker, resulting in a notable photoluminescence quenching. Herein, a well-type Cd_xZn_1−xS/CdSe/Cd_yZn_1−yS QDs is proposed, where ternary alloys CdZnS are adopted to match the lattice parameter of intermediate CdSe by separately adjusting the x and y parameters. The resultant thick-shell Cd_0.5Zn_0.5S/CdSe/Cd_0.73Zn_0.27S QDs reveal nonblinking properties with a high PL QY of 99% in solution and 87% in film. The optimized quantum dot light-emitting diodes (QLEDs) exhibit a luminance of 31547.5 cd m⁻² at the external quantum efficiency maximum of 21.2% under a bias of 4.0 V. The shell thickness shows great impact on the degradation of the devices. The T₅₀ lifetime of the QLEDs with 11.2 nm QDs reaches 251 493 h, which is much higher than that of 6.5 and 8.4 nm QDs counterparts. The performances of the well-type thick-shell QLEDs are comparable to state-of-the-art devices, suggesting that this type of QDs is a promising candidate for efficient optoelectronic devices.     

Tolerance factor and phase stability of the garnet structure. Corrigendum

An error in an equation in the paper by Song et al. [ Acta Cryst. (2019), C 75 , 1353–1358 ] is corrected.     

Extraordinary transport behavior of gases in isothermally annealed poly(4‐methyl‐1‐pentene) membranes

Poly(4‐methyl‐1‐pentene) (PMP) membranes were modified through isothermal annealing to investigate the change of their crystalline structure and rigid and mobile amorphous fractions (RAF and MAF), assuming a three‐phase model, affected the gas transport behavior. The crystalline structure was characterized by wide‐angle X‐ray diffraction (WAXD) and small‐angle X‐ray scattering (SAXS) techniques, and the free volume properties were analyzed by positron annihilation lifetime spectroscopy. Compared with the pristine membrane, the annealed membranes show higher crystallinity; the crystals undergo partial structural change from form III to form I. The lamellar crystal thickness, rigid amorphous fraction thickness, and long period in the lamellar stacks increase with crystallinity. The annealed PMP membranes exhibit higher permeability due to the increase in larger size free volumes in MAF and higher selectivity due to the increase in smaller size free volumes in RAF, respectively. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 2368–2376     

Lattice Boltzmann simulation of liquid–vapor system by incorporating a surface tension term

In this study,we investigate the pseudopotential multiphase model of lattice Boltzmann method(LBM)and incorporate a surface tension term to implement the particle interaction force.By using the Carnahan–Starling(CS)equation of state(EOS)with a proper critical pressure–density ratio,a density ratio over 160000 is obtained with satisfactory numerical stability.The added surface tension term offers a flexible choice to adjust the surface tension strength.Numerical tests of the Laplace rule are conducted,proving that smaller spurious velocity and better numerical stability can be acquired as the surface tension becomes stronger.Moreover,by wall adhesion and heterogeneous cavitation tests,the surface tension term shows its practical application in dealing with problems in which the surface tension plays an important role.